Cold Storage Pioneer in Industrial Design
Roll-Up Doors with flexible PVC curtains provide fast access between production, storage and dispatch areas while helping limit unwanted air exchange. The right specification combines suitable curtain construction, operating speed, motor duty, guidance, sensors and protective devices. For refrigerated openings, temperature, humidity and insulation performance must also be assessed.
A door may open hundreds of times during a shift. Small delays, unnecessary activations and recurring faults can disrupt the whole route. A useful specification therefore begins with the work happening around the opening.
Author: Hamza Ilıman
Last updated: November 16, 2026
Industrial PVC Roll-Up Doors use a flexible curtain that travels vertically through side guides and winds around a shaft above the opening. A powered drive controls movement, while sensors and controls manage activation and protective functions.
Typical components include:
In this guide, the focus is high-speed flexible doors for industrial passages. Fold-up curtains, insulated freezer models and sectional doors have different constructions that should be identified clearly during selection.
Start with the actual use of the opening: warehouse traffic, production separation, dispatch access or refrigerated storage.
Record who passes through, the largest moving load, approach direction, operating hours and peak traffic. Include pedestrians, pallet trucks and forklifts where relevant.
Observe the existing route during a busy period. Vehicles turning immediately before the door may need different detection zones from vehicles approaching in a straight line.
For Roll-Up Doors, distinguish routine passages from occasional oversized deliveries. If people and vehicles share a route, assess a separate pedestrian entrance and suitable traffic management.
The usable passage and the space required for installation are different measurements.
| Site measurement | Why it matters |
|---|---|
| Clear width and height | Determines the usable passage after installation |
| Available headroom | Accommodates the shaft, housing or folded curtain |
| Side clearance | Allows columns, motor and service access |
| Wall construction | Determines the supporting frame and fixing arrangement |
| Finished floor level | Influences bottom sealing and alignment |
| Nearby services | Reveals conflicts with lighting, pipework or sprinklers |
Confirm dimensions from the finished floor and obtain the manufacturer’s installation drawing. Include load overhang and vehicle movement when defining clearance.
Avoid selecting Roll-Up Doors from nominal wall-opening dimensions alone.
Opening speed should suit the required traffic flow, while closing movement must remain compatible with the protective system and site conditions.
For an illustrative constant-speed movement:
Travel time = travel distance ÷ speed
A curtain moving 3 m at 1 m/s would take 3 seconds. Actual opening time also includes acceleration, deceleration and control response.
The complete passage sequence includes detection, opening, hold-open time and closing. A high headline speed provides limited benefit if activation occurs too late or the timer keeps the door open unnecessarily.
Confirm opening and closing speeds separately for the supplied dimensions and control package.
Roll-Up Doors need a drive selected for repeated operation, curtain weight, shaft geometry, friction and the specified movement profile.
Motor power alone does not describe suitability. Ask for the permitted operating duty, starts per hour, peak-cycle capability, brake arrangement and thermal limits.
For example:
200 complete opening-and-closing cycles per day × 300 operating days = 60,000 cycles per year.
This is a usage estimate, not a service-life guarantee.
Where specified, a variable-frequency drive can manage acceleration and deceleration. Its settings must remain coordinated with braking and protective functions. Manufacturer technical literature describes these controls as a way to reduce mechanical stress during movement. hoermann.de
Exterior exposure and internal pressure differences can load the curtain and guides.
For an assumed uniform pressure:
Resultant force = pressure × area
A 4 m × 3 m door subjected to an illustrative 300 Pa pressure difference experiences:
300 × 12 = 3,600 N
This simplified calculation does not determine anchor forces, structural adequacy or the permitted operating wind speed.
For Roll-Up Doors, request the declared wind-resistance classification for the actual door size. Also establish the conditions under which the door may operate. Closed-door resistance and reliable movement under wind require separate confirmation.
EN 12424 provides a classification framework for resistance to wind load. knowledge.bsigroup.com
Curtain selection should consider flexibility, tear resistance, transparency, temperature suitability and cleaning exposure.
Different systems use reinforcement bars, guided edges or modular sections. These arrangements affect how the curtain behaves under pressure and how damaged components are replaced.
For Roll-Up Doors with a curtain re-insertion feature, establish which displacement events the system can recover from and the required inspection procedure afterward. Damage to a column, motor or protective device needs separate attention.
Place vision panels where they support actual sightlines. Keep them clean and check visibility from both pedestrian and vehicle positions.
Each device should have a defined role in the control sequence.
| Device | Typical role | Selection check |
|---|---|---|
| Push button or pull cord | Deliberate opening command | Accessible position outside hazardous movement |
| Motion radar | Detect approaching traffic | Direction, range and unwanted activation |
| Inductive loop | Detect suitable vehicles | Vehicle compatibility and loop location |
| Presence sensor | Detect occupancy within its field | Coverage, stationary detection and stated safety capability |
| Safety-rated light curtain | Monitor a defined protective field | Resolution, coverage and controller compatibility |
| Sensitive bottom edge | Detect contact at the closing edge | Monitoring and validated stopping or reversing response |
BEA’s industrial sensor documentation illustrates the distinction between microwave motion detection and active-infrared presence detection. BEA Sensors
A device used to trigger opening should not automatically be credited with a protective function. Confirm its rating, installation and connection to the safety system.
Roll-Up Doors should be assessed as installed assemblies, including their surroundings, moving parts and control behaviour.
Review closing-edge hazards, accessible drive components, unintended movement and foreseeable use. Specify how the controller responds to an obstruction, a failed protective device and restoration of power.
HSE guidance on powered doors and gates emphasizes the importance of component compatibility, installation and continuing maintenance. HSE
Confirm emergency stopping and the manufacturer-approved method of opening during a power failure. An emergency-stop button does not itself provide access through a closed curtain.
Where an opening forms part of an escape arrangement, its suitability must be established within the building’s approved strategy.
A refrigerated doorway needs both reliable movement and an appropriate thermal barrier.
Record temperatures and humidity on each side, daily cycles, open duration and the arrangement of any insulated door used with the rapid door.
Check curtain insulation, perimeter leakage and component temperature limits separately. A published operating-temperature range does not quantify the assembly’s thermal transmittance.
Freezer installations may require insulated curtains, heated guides or other measures to manage icing. Manufacturer freezer-door documentation shows that these provisions depend on the design. assaabloyentrance.com
For Roll-Up Doors at humid loading areas, assess condensation on cold surfaces and moisture entering the room. Coordinate any vestibule or interlock with traffic and emergency access.
Food-handling areas benefit from accessible surfaces, sealed details and components compatible with the cleaning programme.
Specify cleaning agents, concentration, contact time, water temperature and whether equipment will be washed directly.
Review the curtain, transparent panels, frame finish, fasteners, seals, motor enclosure and control cabinet individually. One component’s ingress-protection rating does not establish the suitability of the complete installation.
Roll-Up Doors should be positioned so that cleaning access remains available around the columns and housing. Avoid details that retain product residue or standing water.
A cleanable door supports hygiene procedures; cleaning effectiveness still depends on how the facility operates and maintains it.
Before installation, verify the supporting structure, opening dimensions, power supply and finished floor.
Set the columns and shaft according to the approved drawing. Protect electrical cables and locate controls where users can operate them safely.
Commissioning of Roll-Up Doors should include:
Testing should follow the manufacturer’s procedures and the applicable assessment method. Record the final settings and any outstanding corrective actions before handover.
Use cycle counts, operating conditions and fault history to set inspection intervals with the manufacturer.
| Symptom | Possible causes to investigate | Appropriate action |
|---|---|---|
| Unwanted openings | Detection field catches cross traffic | Review activation zones |
| Curtain leaves a guide | Impact, pressure or alignment problem | Inspect before reset |
| Uneven bottom contact | Floor variation, wear or incorrect limit | Check geometry and sealing |
| Repeated reversal | Obstruction, dirty optics or device fault | Diagnose the protective circuit |
| Slow or irregular movement | Mechanical resistance or drive problem | Arrange technical inspection |
| Frost at the guides | Moisture entry or heating issue | Review the complete cold-side arrangement |
Maintain Roll-Up Doors without bypassing protective devices. Isolate energy and secure moving parts as required before service work.
Keep records of curtain repairs, sensor replacements and parameter changes. A recurring fault often needs investigation of the operating conditions as well as the component.
Rapid closure can help reduce the time an opening is exposed to air exchange. The benefit depends on the whole operating sequence.
Consider an illustrative route with 200 passages per day:
This compares dwell time only. Opening and closing movements also contribute to air exchange.
For Roll-Up Doors, calculate energy effects using temperature and humidity differences, airflow, leakage, opening dimensions and refrigeration efficiency. Include the door motor, controls and any heaters in the assessment.
A reduction in open time cannot be converted directly into the same percentage reduction in refrigeration electricity. Site measurements provide a better basis for an investment comparison.
| Recommended | Not recommended |
|---|---|
| Select the system around traffic and environment | Choose solely by advertised speed |
| Confirm dimensions and installation clearances | Assume all models fit the same opening |
| Separate activation and protective functions | Treat every sensor as a safety device |
| Verify pressure and wind conditions | Assume an indoor curtain suits exterior exposure |
| Confirm freezer insulation and component limits | Use a general PVC specification for every temperature |
| Investigate recurring faults | Keep resetting without finding the cause |
| Protect columns from vehicle impact | Treat curtain recovery as collision-proof construction |
| Document commissioning and maintenance | Hand over with untested protective functions |
Select standards according to the installation’s location, product classification and intended use.
| Reference | Subject | Evidence to request |
|---|---|---|
| EN 13241 | Industrial door product characteristics | Applicable declarations for the supplied assembly |
| EN 12453 | Safety of power-operated doors | Relevant assessment and test records |
| EN 12424 | Wind-load resistance classification | Declared class and applicable size |
| EN 12426 | Air-permeability classification | Declared leakage performance and test basis |
These references address different performance and assessment subjects. Confirm the applicable editions and project requirements. Listing a standard in a quotation does not by itself demonstrate the supplied door’s performance. landingpage.bsigroup.com
The TunelGroup product range includes the following configurations:
| Model | Construction | Published speed |
|---|---|---|
| FLEX | Reinforced fold-up PVC curtain | 0.7 m/s* |
| ROLL | Rolling PVC curtain | 0.7–1.5 m/s |
| ZIPPER ROLL | Zipper-guided curtain with soft bottom edge | 0.7 m/s* |
| MOD ROLL | Modular curtain with aluminium profiles | 0.7–1.5 m/s |
| FREEZER ROLL | Insulated curtain | 0.7 m/s* |
The marked speeds are published with the EP-500 controller. FREEZER ROLL has a published operating range of −25°C to +40°C. Confirm final dimensions, movement speeds, wind resistance, temperature suitability and equipment scope in the project specification. Tunelgroup Cooling Systems
For a quotation, provide clear opening dimensions, mounting conditions, traffic, environmental conditions, electrical supply and required controls through the TunelGroup contact page.
Common applications include warehouse passages, production areas, packing departments and loading routes. Refrigerated access requires a suitable configuration.
Freezer suitability must be confirmed for the complete assembly, including curtain, guides, drive, controls, sealing and any heating. Specify the required insulation performance separately.
Door size, moving mass, drive, controller and approved settings all contribute. Confirm performance for the actual supplied configuration.
Certain designs can return a displaced curtain to its guides. The function does not repair torn material or damaged hardware.
They can reduce opening exposure when properly controlled. Actual savings depend on air exchange, temperature, humidity, leakage and system efficiency.
Use the manufacturer’s instructions together with cycle count, environment and service history. Busy or demanding installations may require more frequent attention.
Roll-Up Doors support efficient movement when the curtain, drive, detection and protective functions suit the opening. Refrigerated installations also need coordinated insulation and moisture control.
A measured site survey, a complete specification and recorded commissioning checks provide a practical foundation for dependable operation.
Our Mega Structure Design and Manufacturing Efficiency is at the Top Level with Knowledge, Experience and Effective Engineering